PARTS CATALOG INDEX
Accessories Axles Bearings Band Brakes Disc Brakes Cables Cargo Nets Centrifugal Clutches	Chain & Links Chain Lube Engine Parts Gaskets, B&S Jackshafts Kill Switches Manco Parts Max Torque Belts	Mini Bike Parts Mini Chopper Parts Pedals (foot) Rims and Hubs Safety Flags Safety Padding Shock Absorbers Spacers/Bushings	Spark Plugs Sprockets Steering Wheels Throttle Parts Tie Rod Ends Tires & Tubes Tools Page Trouble Shooting	Gear Ratio Chart Go Kart Catalog Mail In Order Form Mini Bike Page Ordering Information Return Policy Service Tips Site Map
Comet Torque Converters: Comet Drive Belts, Clutches & Parts . Home . Parts Catalog
gokartsupply.com

Foot Pedals

Throttle and Brake Pedals Part Number Description Price Add to Shopping Cart 6293-16 BRAKE PEDAL - LEFT 18.99 6309-16 THROTTLE PEDAL - RIGHT 18.99 These pedals are used on Manco go karts. They are considered "universal" and can be used in most any go kart application.

Throttle and Brake Pedals Part Number Description Price Add to Shopping Cart 1806 FOOT PEDAL BRAKE SIDE 7.50 1811 FOOT PEDAL THROTTLE SIDE 7.50 Zinc plated pedals with a built in stop. 4 position rod mounting. Mounting bolt 5/16-18 x 1-3/4"

Hand Controls

Twist Grip Sets Part Number Description Price Add to Shopping Cart 04-257 TWIST GRIPS 7/8" HANDLEBARS 15.99 04-258 TWIST GRIPS 1" HANDLEBARS 15.99 Measure your handlebars before ordering. Each set includes cable-end adjuster part # 04-268 (shown below).

Ball End Brake Lever For 7/8" Handlebars Part Number Description Price Add to Shopping Cart 1731 BRAKE LEVER 7/8" HANDLEBARS 13.99 Replacement brake lever for 7/8" handlebars, includes cable adjuster. Universal Application.

Cable Hardware

Twist Grip Ferrule Part Number Description Price Add to Shopping Cart 04-268 ADJUSTER-CABLE END 1.79 This ferrule is used on many twist grips to hold the housing in place.

Tecumseh Cable Stop - Swivel Part Number Description Price Add to Shopping Cart 2361 TECUMSEH CABLE STOP 2.99 Use these cable wire stops with Tecumseh engines. Many Manco go karts with Tecumseh engines require this particular cable wire stop. (It's smaller in diameter than those used with Briggs and Stratton engines)

Swivel Wire Stop Part Number Description Price Add to Shopping Cart 04-267 WIRE STOP-SWIVEL 1.25 This universal wire stop will work on throttle cables and brake cables.

Round Wire Stop Part Number Description Price Add to Shopping Cart 04-219 WIRE STOP-ROUND 1.25 This round wire stop is used for securing the inner wire to the engine.

Briggs and Stratton Conduit Clip Part Number Description Price Add to Shopping Cart 03-250 BRIGGS C0NDUIT CLIP 1.25 Bolt on. Used to clamp the throttle cable to the engine. Zinc plated. Complete with screw. Replaces Briggs and Stratton Part #22372.

Throttle Cable Assembly Instructions

Pass the throttle cable through the cable retainer and butt the throttle cable housing end against the inside shoulder of the cable retainer. (The cable retainer is to be securely fastened to the engine with the clamping screw.) Pass the end of the cable through the hole in the cable stop. Before tightening the cable stop screw:

• Ensure the spring anchor, spring and cable are installed as illustrated above.
• Ensure the throttle pedal is in the rearward (idle) position.
• Ensure that there is no slack in the throttle cable with no tension applied to the return spring.
• Ensure the cable housing is inside and against the cable retainer.

The part numbers on the illustration above are part numbers used by Manco Products only. These are not the Briggs and Stratton part numbers.